65.23mm 60.6mm 39.7mm + ic height a a top view side view front view section a-a all tolerances: 0.125mm (unless stated otherwise). materials and specifications are subject to change without notice. status: released drawing: e smolentseva scale: - rev: a date: 7/14/10 file: CG-BGA-4013 dwg CG-BGA-4013 drawing modified: page 1 of 4 features directly mounts to target pcb (needs tooling holes) with hardware minimum real estate required compression plate distributes evenly clamshell lid compression plate: black anodized aluminum. thickness = 12 mm. compression screw: clear anodized aluminum. height = 27 mm, fluted knob socket base: black anodized aluminum. height = 6 mm. clam shell lid: black anodized aluminum. height = 20 mm. socket base screw: socket head cap screw, black oxide, 0-80 thread, 5/8" long. backing plate: black anodized aluminum insulation plate: fr4/g10 1 m a t e r i a l s : 2 3 4 5 6 7 8 9 latch: black anodized 7075 aluminum. 10 11 1 2 customer's pcb 6 5 3 4 8 9 10 7 11 ? 2010 ironwood electronics, inc. 11351 rupp drive, suite 400, burnsville, mn 55337 tele: (952) 229-8200 www.ironwoodelectronics.com elastomer guide: non-clad fr4. thickness = 0.725mm. elastomer: 40 micron dia gold plated brass filaments arranged symmetrically in a silicone rubber (63.5 degree angle). thickness = 0.75mm. ball guide: kapton polyimide.
page 2 of 4 recommended pcb layout tolerances: 0.025mm [0.001] unless stated otherwise. r e c o m m e n d e d p c b l a y o u t t o p v i e w t a r g e t p c b r e c o m m e n d a t i o n s total thickness: 2.4mm min. plating: gold or solder finish pcb pad height: same or higher than solder mask note: steel backing plate may be required based on end user's application status: released drawing: e smolentseva scale: - rev: a date: 7/14/10 file: CG-BGA-4013 dwg CG-BGA-4013 drawing modified: ? 2010 ironwood electronics, inc. 11351 rupp drive, suite 400, burnsville, mn 55337 tele: (952) 229-8200 www.ironwoodelectronics.com non plated mounting hole non plated alignment hole orientation mark 1.25mm 0.13mm (x4) 1.25mm 0.13mm (x4) 50.23mm 0.125mm (x4) 5.08mm 23.8625mm(x8) 1.27mm typ. 2.54mm ? 0.85mm 0.025mm (x2) ? 0.64mm pad (x1152) 3.2825mm* socket size 2.9075mm 52.73mm 0.125mm (x4) 2.5mm 0.13mm 2.5mm 0.13mm backing plate size ? 1.71mm 0.1mm (x8) * n o t e : b g a p a t t e r n i s s h i f t e d t o t h e r i g h t b y 0 . 3 7 5 m m w i t h r e s p e c t t o t h e m o u n t i n g h o l e s .
page 3 of 4 status: released drawing: e smolentseva scale: - rev: a date: 7/14/10 file: CG-BGA-4013 dwg CG-BGA-4013 drawing modified: ? 2010 ironwood electronics, inc. 11351 rupp drive, suite 400, burnsville, mn 55337 tele: (952) 229-8200 www.ironwoodelectronics.com c o m p a t i b l e b g a s p e c d e y x ?b top view side view 0.20 bottom view e detail dim min max a 2.51 a1 0.5 0.7 b 0.90 d e e 45 bsc 45 bsc 1.27 bsc 3 4 5 dimensions are in millimeters. interpret dimensions and tolerances per asme y14.5m-1994. dimension b is measured at the maximum solder ball diameter, parallel to datum plane z. datum z (seating plane) is defined by the spherical crowns of the solder balls. parallelism measurement shall exclude any effect of mark on top surface of package. 1. 2. ?0.30 z x y 3 ?0.15 array: 34 x 34 a a1 detail 0.2 z z 0.35 z 5 4
page 4 of 4 side view top view description: b a c k i n g p l a t e w i t h i n s u l a t i o n p l a t e all dimensions are in mm. all tolerences are +/- 0.125mm. (unless stated otherwise) status: released drawing: e smolentseva scale: - rev: a date: 7/14/10 file: CG-BGA-4013 dwg CG-BGA-4013 drawing modified: ? 2010 ironwood electronics, inc. 11351 rupp drive, suite 400, burnsville, mn 55337 tele: (952) 229-8200 www.ironwoodelectronics.com note: backing plate holes are tapped to accept 0-80 screws. 1.59mm 6.35mm insulation plate backing plate 52.73mm 52.73mm 2.5mm 2.5mm 23.8625mm 0.025mm (x8) 23mm (x4) 10mm sqr. 1.27mm (x4) 5mm 8.53mm ? 1.71mm 0.1mm (x8)
|